Savage, Minnesota
Durable Metal Roofing in Savage, MN
Wind is the argument for metal in Savage, not snow. The river valley runs west-southwest to east-northeast right past town, and a west wind funnels down it, so the plats on top of the hundred foot bluff above Highway 13 take gusts that inland streets never feel. Standing seam, clipped and screwed into solid deck, holds where tabs lift.
Get your estimate today
Rated 5.0 from 217 Google reviews
- Licensed and insuredMinnesota exterior contractor
- 5.0 from 217 reviewsVerified on Google
- Storm and insurance workWe handle the claim with you
- Faith-based, locally ownedRefreshingly honest
Cut up rooflines decide the panel plan
The two story homes above the valley here were built in the 1990s and early 2000s with rooflines that fold back on themselves. An upper gable dumps onto a lower plane, that plane runs into a short valley, and the valley turns again before it reaches a gutter. Standing seam on a roof like that is mostly transitions, and transitions are where the labor and the risk sit. We run the panels as long as the geometry allows, form the valley metal wide, and set snow retention above the lower plane so a winter slide does not tear the gutter off. On the bluff lots near the fen, where the ground drops hard toward the river, staging is its own line on the quote. Homeowners planning a whole exterior sometimes pair this with our luxury roofing work on the same house, and we will schedule them together.
Metal Roofing in Savage
What good metal work does on these roofs
Wide valley metal where planes meet
Upper gables on these homes drain into short valleys that carry a lot of water fast. We form valley metal wide and open so the flow clears instead of backing up under a seam.
Several short ridges, one venting plan
A roof that folds back on itself does not have one long ridge to exhaust through, it has three or four short ones at different heights. We work out where the air actually leaves before the panel goes on, because a vent run broken up by the geometry stops doing its job quietly.
Edge and rake metal for a west gust
Wind coming up the valley corridor works on edges first. Perimeter clips get tightened, eave and rake trim get locked in, and that detailing is what keeps a panel from peeling at the corner.
Gutters sized for a steep shed
Metal moves water off the roof faster than asphalt does. On a two story with a steep upper gable, that means the gutter and downspout below need to be sized for the volume they will suddenly get.
Quieter under a two story roof
People expect drumming. Over a solid deck, synthetic underlayment and an insulated attic, rain on standing seam reads as a low hum in the upstairs bedrooms, not the noise you remember from a farm shed.
The upper gable stops dumping
Metal sheds snow in one slab. Where an upper gable unloads onto a lower plane, we set retention above the transition so the slide does not strip the gutter or crack the roof below.
Why homeowners here call us for metal
We map the panel layout first
Before anything is ordered we draw where each run starts and stops, so seams land at the transitions instead of partway across an open plane. On a roof shaped like this one, that drawing is most of the job.
The quote names panel and gauge
You should know the profile, the steel gauge, the finish and the clip type before you sign. We put those in writing so you can compare our number against anyone else's honestly.
We check what your lot catches
A plat on the bluff above Highway 13 and a street tucked inland get different wind. We look at your exposure before deciding how tight the perimeter fastening needs to be.
We protect the ground below
Lots near the fen drop away hard toward the river valley. We tarp and stage so torn shingles, screws and offcuts do not end up down the slope where nobody can reach them.
We tell you what it wants afterward
A seamed roof asks very little of you, but sealant at a chimney and debris caught in a short valley still want a look every couple of years. We write down what to check and where, so you are not guessing at what a metal roof needs.
What people near Savage say
Orange Exteriors fixed a minor leak that involved replacing flashing and a few shingles blown off our roof. Timely, quality work. Great ideas to keep our roof going long term.
Jim ThomasStorm damage repair From sales to construction crew to upper management, they helped make an insurance battle a breeze. This is the best contractor interaction I have ever had.
Jim NormanRoof replacement Orange Exteriors did an excellent job with my new roofing install. Very professional, on time and hard working crew. Completed the job in one day.
Dick JohnsonRoof installation
Questions we get in Savage
What people in Savage ask us about this work. If yours is not covered, call and ask.
The house is from 1998. Does the sheathing under it matter for metal?
It matters, and it is a different question than on an old house. Sheathing from the late 1990s is usually panel goods rather than boards, and it holds a clip well as long as it has stayed dry. Where it has been wet it swells at the edges and loses its grip, and on your roof that means the valleys and the old vent penetrations. We check those areas as the deck comes open and replace what has gone soft.
My upper gable sheds onto a lower roof. Does metal make that worse?
It changes it. Asphalt holds snow in place until it melts. Metal releases the whole load at once, and on your roof that load lands on a lower plane and a gutter. The fix is snow retention set above the transition, sized for the slope and the run. We plan it as part of the job, not as an add on later.
Does a heavier gauge make sense up on the bluff?
For wind, not really. What holds a panel down is clip spacing, the deck behind it and how the edge metal is locked in, and a heavier gauge does not change any of those. Where gauge earns its keep is stiffness and denting: a heavier panel stays flatter across a wide plane and marks less. We name the gauge on the quote either way, so you can compare it against anyone else's number.
Have us look at your Savage roofline
Send us the address and we will get up on it, count the valleys and transitions, and tell you what standing seam would take on that particular house.
Get Your Free Exterior Estimate
Tell us what is going on with your roof, siding, windows, or gutters. We will take a look and give you a straight answer, including when the answer is that you can wait.
- Phone(612) 600-8529
- Emailadmin@orange-exteriors.com
- Office6600 City West Pkwy Suite 375, Eden Prairie, MN 55344
- HoursOpen 24 hours, Sunday to Saturday
Request your estimate
Rated 5.0 from 217 Google reviews